Monitoring Status Gangguan Listrik Pada Saluran Distribusi Berbasis Arduino

Dino Dwi Putra(1), Oriza Candra(2),
(1) Universitas Negeri Padang  Indonesia
(2) Universitas Negeri Padang  Indonesia

Corresponding Author


DOI : https://doi.org/10.24036/jtev.v7i1.111455

Full Text:    Language : id

Abstract


Abstract  power is a source of strength that has a very critical role in normal existence, beginning from domestic affairs, workplaces, and so forth. If the electricity is cut off or dead, a lot of work using these electronic devices will be neglected. If a power cut occurs due to a disruption in the distribution line, the public can provide an information report in the form of a telephone call or visit the PLN office to report to the operator if in their area the electricity has problems. However, unlike people in areas such as rural areas, there is very little attention to this kind of information and it is difficult for operators to monitor distribution channels in the area. Therefore, it is necessary to make a monitoring tool for the status of electrical disturbances on an Arduino-based distribution channel, so that if there is a disturbance or disconnection in the distribution channel it can be quickly detected. Where the system works with the Arduino Mega2560 control and is monitored using Android via the Blynk programming. The system begins by activating the device and is continued by connecting (pairing) the ESP8266 with Android Wifi, with the name test wifi and password 88888888, if it is connected, the user can open the Blynk application on a Smartphone. The ACS712 sensor on the device is used to detect current and the ZMPT101B sensor is used to detect voltage and the results of the reading will be processed by Arduino Mega2560. Then if there is a short circuit / disconnection of electricity in the power line, the notification will enter the android via the Blynk application. The process of sending data from Arduino is carried out by ESP8266 which has been configured with Arduino. So that monitoring of disturbance status can be seen on Android


Keywords


Arduino Mega, ZMPT101B Sensor, Electrical Interference Monitoring

References


R. Anggriawan and O. Candra, “Rancang Bangun Pengaman Pintu Ruang Kuliah Menggunakan Sensor Fingerfrint Berbasis Arduino Mega2560,” vol. 6, no. 1, pp. 25–34, 2020.

Z. Abidin and M. Baha’udin, “Monitoring Dan Proteksi Tegangan Panel 3 Fasa Dengan Menggunakan Sensor Tegangan ZMPT101B,” pp. 1–8.

T. Akhir, “Prototype Sistem Monitoring Gardu Distribusi,” 2019.

J. Asmi and O. Candra, “Prototype Solar Tracker Dua Sumbu Berbasis Microcontroller Arduino Nano dengan Sensor LDR,” JTEV (Jurnal Tek. Elektro dan Vokasional), vol. 6, no. 2, p. 54, 2020, doi: 10.24036/jtev.v6i2.108504.

H. Koyuko, A. A. E. Sinsuw, and X. B. N. Najoan, “Perancangan Aplikasi Monitoring Pemadaman Listrik Berbasis Android Studi kasus PT.PLN area Manado,” J. Tek. Inform., vol. 9, no. 1, 2016, doi: 10.35793/jti.9.1.2016.13903.

I. Anugrah, “Pengukur Daya Listrik Menggunakan Sensor Arus ACS712-05A dan Sensor Tegangan ZMPT101B,” pp. 1–80, 2017, [Online]. Available: http://eprints.uny.ac.id/id/eprint/60197.

O. Candra, “Rancang Bangun Sistem Kontrol Bucket Elevator Berbasis Mikrokontroler,” 2009.


Article Metrics

 Abstract Views : 606 times
 PDF Downloaded : 222 times

Refbacks

  • There are currently no refbacks.